Beside the common advantages of a flyback converter, it has inherently parasitic components, which typically produce ringing waveforms with considerably high voltage spikes. This ringing can also influence the EMI emissions adversely. Therefore, it is an important task to adequate suppress and damp the ringing effect....
Published: Jul 01, 2021
Racks organize IT equipment, such as servers and network switches, into standardized assemblies that make efficient use of space and other resources. Depending on the options you choose, they can also improve power protection, cooling, cable management, device management, physical security, mobility, ease of installation...
Published: Jul 25, 2018
Radar, satellite communications and 5G NR use AAS with phased array antennas for beamforming. Hybrid beamforming combines the flexibility of digital beamforming with the efficiency of analog beamforming.
Increasing integration enables compact and cost-efficient AAS. To achieve accurate, reliable and efficient beamforming,...
Published: Sep 03, 2020
This introduction to EPAD MOSFET describes a broad selection of devices with precisely set gate threshold voltage values, including zero threshold made, enhancement mode and depletion mode. Furthermore, novel circuit designs are presented to illustrate how these devices can be used at a practical level. The brief circuit...
Published: Jul 18, 2018
A transition to 400 VDC in power distribution and conversion will help meet greenhouse gas, efficiency, and renewable-energy goals.
The pressure throughout the energy supply chain to deliver electrical power more efficiently is intense and growing. Most dramatically, the European Union’s response to the Copenhagen...
Published: Jul 23, 2018
Manufacturers are facing increasing pressures to get their products to market faster. One way to save vital time is to work with a partner who can provide value added design and assembly services. Distributors such as TTI can provide the expertise and resources needed to accelerate these processes.
In this whitepaper,...
Published: Feb 15, 2019
The digital signage market is experiencing rapid growth. Organizations across a wide range of industries are making large investments in the content, source machinery and displays that comprise digital signage systems. The choice to protect these investments from power problems is crucial—yet frequently overlooked....
Published: Jul 25, 2018
PCI was originally designed as an interconnect for personal computers; because of the nature of PCs at that time, the protocol architects did not anticipate the need for multiprocessors. Therefore, they designed the system assuming that the host processor would enumerate the entire memory space. Obviously, if another processor...
Published: Jul 17, 2018
In traditional networking management, it can take a lot of time to configure each network device with duplicate settings, as well as perform firmware synchronization. If, after deployment, an issue appears without an obvious method of solving, it can quickly affect the efficiency of the network.
B+B SmartWorx IXM...
Published: Jul 18, 2018
QMatrix devices are digital charge-transfer (QT) ICs designed to detect touch using a scanned, passive matrix of electrode sets to achieve a large number of touch keys driven by a single chip.
This configuration leads to a high pin count efficiency in the sensing chip and allows for a small number of connections between...
Published: Jul 23, 2018
Today's high reliability military, aerospace, and industrial applications require more rugged, light - weight filter connectors. The filter connector provides a stray signal barrier upstream and away from electronic devices to protect critical circuits from electrical interference, without affecting system function...
Published: Jul 25, 2018
Every electronic system needs a timing device. And crystal (XTAL) resonators are often the go-to solution. However, oscillators, which pair a resonator with an oscillator IC into one complete integrated timing device, offer several benefits compared to XTALs. These benefits are further extended with MEMS timing technology....
Published: Jul 16, 2018
The output signal of an oscillator, no matter how good it is, will contain all kinds of unwanted noises and signals. Some of these unwanted signals are spurious output frequencies, harmonics and sub-harmonics, to name a few.
The noise part can have a random and/or deterministic noise in both the amplitude and phase...
Published: Jul 25, 2018
It is apparent that many older specifcations for government and military security contacts were based around the misconception that Balanced Magnetic Switches (BMS) or Triple balanced reed switches provide the highest possible security. While it is true that BMS / Triple balanced reed devices do provide “better”...
Published: Jul 19, 2018
